Designed for drying or drying in laminar flow air. The vertical dryer has 6 carpet trays enclosed in the drying chamber, moved by means of a special up / down system. Through the vertical movement, each tray is cyclically brought to the loading and unloading windows where, with synchronized speed to that of the line, the output of the dried pieces and the load of freshly painted pieces takes place simultaneously. The semi-closed-circuit ventilation system guarantee a controlled air flow, which is guided between the trays by targeted openings and side closing barriers.
VERTICAL DRYING OVEN FEATURES

Vertical dryer with belt trays
Drying system with belt trays
The Contivert Dryer with belt trays has all the advantages of a linear dryer, while requiring only a minimum of space and energy. Belt trays arranged one on top of the other ensure controlled air flow, with both its speed and temperature adapted to the drying cycle and the finishing material used
Loading and Unloading, complete batches, cycle by cycle
The machine’s operating sequence:
The conveyor belt is set in motion as soon as a belt pallet coming up from below has reached the loading and unloading level and a batch of freshly lacquered work-pieces has been identified by the photocell. After the loading of a new batch and the unloading of the dried work-pieces have been completed, the following movements are carried out simultaneously in the Convert:
- The belt tray which has just been loaded moves up by one cycle in only 2,5 seconds (1 cycle=1 rack stage)
- The next belt tray starts moving up and reaches the loading and unloading position
- The belt tray on the top starts moving in the next cabin
- The belt tray at the bottom starts moving in the previous cabin
The necessary number of belt trays
The model of the Contivert, the number of the belt trays and the overall height of the dryer are determined by:
- The output of the upstream lacquering unit (coating and automatic spraying machine)
- The drying cycle specified by the lacquer manufacturer
The maximum work-piece thickness in the contivert depends on the distance between trays
The thickness of the workpieces to be dried determines the distance between the belt pallets (rack clearance) and therefore as a consequence the number of the belt pallets possible in the relevant Contivert model of a certain height. A sufficient distance between the belt pallets is essential to ensure correct air circulation over the work-pieces and therefore effective drying
The Contivert can be equipped for any of the following workpiece thickness:
- Max thickness : 60 – 90 – 150 mm
- Distance (rack clearance) : 90 – 120 – 180 mm

The contivert design concept has the following models:

Six-daylight dryer, suitable for flash off and drying cycles with laminar air flow. Typical drying time from 5 to 15 minutes according to the finishing line feed speed
- Contivert ETC 3/2
Consisting of 2 cabins with belt pallets and 1 cabin for spacing
Two cahmbers vertical dryer; it can contain from 18 up to 60 trays. Work-pieces in-feed and out-feed are in this case in the same line, as indicated in the first sketch on the opposite page.


- Contivert ETC 4/4
Consisting of 4 cabins with belt pallets

Belt dryer with belt pallets
The contivert drying system, with separate zones with individually controlled settings
The Contivert system (patented) is based on pallets equipped with conveyor belts. These belts pallets move mechanically – vertically and horizontally in cycle – through the Contivert unit, which is divided into a flash off zone, two temperature-controlled heating zones and a cooling zone, all with variably controlled air speeds. The air flow is restricted in the upward and downward direction by the belt pallets and to the sides by baffle plates

The contivert force ventilation circuit with partial air regeneration
The flash off and cooling zones are located in the lower part of the unit. The air flow is blown into the cooling zone. During the cooling process, the air is heated by the workpieces and the belt pallets and then it is blown into the flash off zone, at the end of which another fan guides it out of the unit. The heating zones in the upper part of the unit work according to the recirculating air principle. Air is guided through the two heating zones at different temperatures

Belt tray vertical dryer
Contivert is a high quality drying solution that ensures the most careful treatment of the coated surface; also in case of delicate finishes, including glossy ones. The pieces to be dried are on the fully supported belt pallets, so as to have a uniform temperature over the entire lower surface of the work piece. The air flow over the work-pieces is well controlled, since the air is easily managed between the two closed and linear surfaces of the stacked pallets. All movement devices are located outside the drying area of the belt pallets
The ideal solution for high-capacity production lines:
It requires minimal time between loads, without any necessity of a load acceleration zone in the entrance area (the zone quite frequently required in dryers with bar pallets) The whole line is highly productive and space saving

VERTICAL DRYER TECHNICAL DATA
| Model | VD6000-6 |
| Working width | 1300mm |
| Max. part length | 5700mm |
| Max. part thickness | 50mm |
| Number of pallets | 6 trays |
| Tray length | 6000mm |
| Drying temperature | 55-60℃ |
| Feed speed infinitely adjustable | 2 – 10 m/min |
| Feeding power | 0.37+0.75+0.37KW |
| Heating power | 24KW |
| Lifting power | 2.2kw |
| Exhaust blower | 0.37KW |
| Circular blower power | 0.75KW |
| Air pressure | 0.6-0.8Mpa |
| Dimension | 7400X2200X3000 |
| Weight | 3000KG |
Vertical Dryer Footprint

Application of the Vertical Dryer
























